Rough-country 609S Bedienungsanleitung PDF herunterladen

JEEP JK 3 1/2” SUSPENSION KIT

W/ ROUGH COUNTRY N2.0 SHOCK ABSORBERS

Thank you for choosing Rough Country for your suspension needs.

Please read instructions before beginning installation. Check the kit hardware against the parts list. Be sure you have all

needed parts and know where they go. Also please review tools needed list and make sure you have needed tools.

PRODUCT USE INFORMATION

Rough Country Suspension products are intended to improve off road performance. Modifying your vehicle for off road

use may result a vehicle in the vehicle handling differently than a factory equipped vehicle. Avoid situations where a side

rollover may occur. Seat belts and shoulder harnesses should be worn at all times.

Do not add, alter, or fabricate any factory or after-market parts to increase vehicle height over the intended height of the

Rough Country product purchased. Mixing component brands is not recommended.

This 3 1/2” suspension system was developed using a 35X12.50X17 tire with 4.5” to 4.75” of back spacing on aftermar-

ket wheels. Stock wheels can be used with this kit with up to a 35x12.5 tire, but different tire manufactures designs may

result in a tire width that could result in contact with the lower control arm and/or front sway bar link in a sharp turn.

Please consult with your tire and wheel expert before purchasing. Stock Wheels can be used with the addition of a 1 1/2”

wheel spacer.

If questions exist we will be happy to answer any questions concerning the design, function, and correct

use of our products by calling 1-800-222-7023.

IMPORTANT NOTES : Upon completing the install of this kit the draglink must be adjusted to center the steering

wheel BEFORE

the vehicle is driven. Failure to do so will cause the Vehicle Stability Program to not function

properly , odd vehicle handling, and poor performance.

On 07-11 Automatic equipped vehicles; due to use of an oversize driveshaft from the factory and inade-

quate factory clearance it may be possible for the front driveshaft to come in contact with the automatic trans-

mission pan tearing the factory boot and rubbing on the shaft. Generally this occurs during heavy articulation

when front sway bar links are disconnected and longer shocks are installed. If this is found to occur, the proper

procedure would be to replace the oversize factory shaft with an aftermarket smaller diameter shaft to increase

clearance between the transmission and front driveshaft. Rough Country does offer this driveshaft if needed.

Also on 2012 Models, additional exhaust modification on the passenger side crossover pipe will be required for

adequate clearance on the front driveshaft.

NOTICE TO DEALER AND VEHICLE OWNER

Any vehicle equipped with any Rough Country product should have a “Warning to Driver” decal installed on the inside of

the windshield or on the vehicle’s dash. The decal should act as a constant reminder for whoever is operating the vehi-

cle of its unique handling characteristics.

92160900

GRD-5 GRD-8

5/16” 15 ft/lbs 20 ft/lbs

3/8” 30 ft/lbs 35 ft/lbs

7/16” 45 ft/lbs 60 ft/lbs

1/2” 65 ft/lbs 90 ft/lbs

9/16” 95 ft/lbs 130 ft/lbs

5/8” 135 ft/lbs 175 ft/lbs

3/4” 185 ft/lbs 280 ft/lbs

Metric (Grade) 8.8 10.9 12.9

14MM 85ft/lbs 120ft/lb. 145ft/lbs

Torque Specifications

Jack

Jack Stand

13/32” Drill Bit

Drill

Pitman arm puller

WD-40

3/8” Drill Bit

21mm Socket

21mm Wrench

7/16” Wrench

9/16” Wrench

9/16” Socket

Tools Needed:

10mm Wrench

14mm Wrench

16mm Wrench

18mm Wrench

18mm Socket

19mm Wrench

19mm Deep Well Socket

7/8” Wrench

13/16” Socket

1 2 3 4 5 6 7 8 9 10

Inhaltsverzeichnis

Seite 1

JEEP JK 3 1/2” SUSPENSION KIT W/ ROUGH COUNTRY N2.0 SHOCK ABSORBERS Thank you for choosing Rough Country for your suspension needs. Please read inst

Seite 2

21. Slide the metal mount to the end of the line and reinstall the diff vent hose on the frame as shown in Photo 12. 22. Reinstall the rear tires/whee

Seite 3

Front Track Bar Bracket RR Bump-stop brkts Rear N2.0 Shocks Pitman Arm Rear Track Bar Bracket Rr Sway Bar Links Rear Coil (2) Front Coil Springs (2) B

Seite 4

FRONT INSTALLATION INSTRUCTIONS 1. Prior to installing this kit, with the vehicle on the ground, measure the heights of your vehicle. This measu

Seite 5

11. Install the new control arms in the upper mount as shown in Photo 5 with the stock hardware. 12. Install the arm on the axle with the stock hardw

Seite 6

18. Lightly lube pitman arm splines with WD-40 and install the new pitman arm with the stock hardware. Tighten using a 33mm socket. See Photo 11. Rein

Seite 7

24. Install the two 3/8” x 1 1/4” bolts, washer and nuts in the new bracket and supplied stabilizer bracket if reusing the stock stabilizer in the far

Seite 8

33. Locate the brake line bracket and install using the stock hardware. Install the stock brake line on the other end of the bracket using the supplie

Seite 9

PHOTO 2 REAR INSTALLATION INSTRUCTIONS 1. Jack up the rear of the vehicle and support the vehicle with jack stands, so that the rear wheels are off

Seite 10

14. Insert the supplied sleeve, inside the factory track bar mount. Insert the supplied 14mm” x 80mm” bolt through the bracket, factory mount, and sle

Kommentare zu diesen Handbüchern

Keine Kommentare

Rough-country 609S Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rough-country 609S herunter. Rough Country 609S User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rough-country 609S