Rough-country 276P Bedienungsanleitung PDF herunterladen

88-98 GM 4”- 6” SUSPENSION KIT

92127400

Tools Needed

10mm Wrench 1 1/16” Wrench

11mm Wrench 7/8” Socket

13mm Socket 3/8” Allen Head

14mm Wrench Grinder

15mm Wrench Saw

15mm Socket Jack Stands

18mm Wrench Reciprocating Saw

18mm Socket

21mm Wrench

21mm Socket

24mm Socket

24mm Wrench

35mm Socket

Thank you for choosing Rough Country for your suspension needs.

Rough Country recommends a certified technician installs this system. In addition to these instructions, professional

knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install

this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read all the instructions before beginning the installation. Check the kit hardware against the parts list. Be sure

you have all the needed parts and understand where they go. Also please review the tools needed list and make sure

you have needed tools.

PRODUCT USE INFORMATION

As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend, because of rollover possibility, that

seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur.

Braking performance and capabilities are decreased when significantly larger/heaver tires and wheels are used. Take

this into consideration while driving. Also, speedometer recalibration is necessary when larger tires are installed.

Do not add, alter, or fabricate any factory or after-market parts which increase vehicle height over the intended height of

the Rough Country product purchased. Mixing component brands, lifts, and/or combining body lift with suspension lifts

voids all warranties. Rough Country makes no claims regarding lifting devices and excludes any and all implied claims.

We will not be responsible for any product that is altered.

This kit is packaged as a leveling kit. If you desire a different look or if your truck has a tool box or something else that is

going to bring the rear end down, please consult with your sales person about higher block and u-bolt options. If your

vehicle is equipped with a rear sway bar (Tahoe and Suburban standard equipment), we recommend that you

purchase longer sway bar links, part # 1038. Steering Stabilizer Part # 87369 is also available from Rough Coun-

try for use with this kit.

Important Note:

4 Door Tahoe’s and Yukon’s require part number 89501 torsion bar cross member bracket in

addition to the standard kit to complete installation, if you have not ordered/received 89501 – Torsion Bar Kit,

then please call your Rough Country distributor before

you begin installation.

NOTICE TO DEALER AND VECHICLE OWNER

Any vehicle equipped with any Rough country product must have the “Warning to Driver” decal installed on the sun visor

or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling character-

istics. INSTALLING DEALER—It is your responsibility to install the warning decal and to forward these installation in-

structions on too the vehicle owner for review and to be kept in the vehicle for its service life.

Torque Specs

Size Grade 5 Grade 8

5/16” 15 ft/lbs 20 ft/lbs

3/8” 30 ft/lbs 35 ft/lbs

7/16” 45 ft/lbs 60 ft/lbs

1/2” 65 ft/lbs 90 ft/lbs

9/16” 95 ft/lbs 130 ft/lbs

5/8” 135 ft/lbs 175 ft/lbs

3/4” 185 ft/lbs 280 ft/lbs

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1

88-98 GM 4”- 6” SUSPENSION KIT 92127400 Tools Needed 10mm Wrench 1 1/16” Wrench 11mm Wrench 7/8” Socket 13mm Socket 3/8” Allen

Seite 2

58. Locate the kicker braces from 1274Box1. Install the bushings and sleeves from 1274bag5, into the end of the kicker braces. Using the 1/2” x 3.5” b

Seite 3 - See Photo 2

64. Attach the two skid plates together using the 4-3/8” x 1” bolts from 1274bag3. Torque to 30 ft/lbs. See Photo 45. 65. Install part # 657341 hydro

Seite 4 - Photo 9

REAR INSTALLTION 1. Chock front wheels and jack up the rear of the vehicle. Secure with jack stands on the frame rail. 2. Place a floor jack under

Seite 5 - Photo 16

Lower Skid Plate Rear Cross Member Steering Assembly Upper Control Arm Drop Upper Control Arm Drop Torsion Bar Drop Torsion Bar Drop Kicker Brace Kick

Seite 6 - Photo 21

FRONT INSTALLTION INSTRUCTIONS 1. Chock the rear wheels to prevent movement. Place a jack under the lower control arm and jack the vehicle up. Plac

Seite 7 - Photo 26 Photo 27

9. Using an 18 mm wrench remove the nut holding the drag link to the knuckle. It may be necessary to hit the knuckle with a hammer to dislodge the dr

Seite 8 - Photo 33

17. Using a 13mm socket and wrench remove the sway bar link. Save the stock hardware. 18. Remove the bolts holding the lower control arm, using a 24m

Seite 9 - Photo 36

26. Using a 21mm wrench and socket remove the upper bolt that holds the differential. Remove the differential from the vehicle. Do not remove the pass

Seite 10

32. Place the driver side upper control arm drop bracket from 1274 Box 2, into the stock upper control arm brackets as seen in Photo 22 & 23. Bolt

Seite 11 - Photo 49 Photo 50

39. Bolt the second differential bracket to the upper axle mount on the passenger side using the 9/16” x4” bolts, washers and nuts provided in 1274bag

Seite 12

44. Swing up the bracket and insert the supplied crush sleeve in the frame rail for the existing hole on the upper control arm drop bracket Take care

Kommentare zu diesen Handbüchern

Keine Kommentare

Rough-country 276P Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rough-country 276P herunter. Rough Country 276P User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rough-country 276P