Rough-country 1173 Bedienungsanleitung PDF herunterladen

JK WINCH / D-RING MOUNTING SYSTEM

Thank you for choosing Rough Country Off road Products

Please read instructions before beginning installation. Check the kit hardware against the parts list and product layout.

Be sure you have all needed parts and know where they go. Also please review tools needed list and make sure you

have needed tools.

If questions exist we will be happy to answer any questions concerning the design, function, and correct use of this prod-

uct.

The installer must verify that the mounting kit does not interfere with the factory air bag sensors, which must not be relo-

cated or modified in any way. The vehicles air bag system may not operate properly if the winch mounting kit is not

mounted in compliance with the vehicle manufacturers recommendations.

Winch mounting should only be performed on vehicles with standard OEM bumpers.

Please note the tightening sequence on the last page. This sequence must be followed to ensure proper fit of

winch plate and winch plate brackets.

Note: If the vehicle is equipped with factory bumper shims, these will not be reused.

INSTALLATION INSTRUCTIONS

1. Place vehicle on a flat surface and set emergency brake.

2. Using a small phillips screwdriver, remove the 2 plastic screws on top of the front bumper cover. Retain Stock hard-

ware. See Photo 1.

3. Remove the 4 plastic screws holding the skid plate to the front bumper, using a small Phillips screw driver Retain

stock hardware. See Photo 2.

Kit Contents

1– Mounting Plate

2– Front Mounting Brackets

1– Driver Side Mounting Brk

1– Pass Side Mounting Brk

1-Dr side d-ring bracket

1-Pass side d-ring bracket

2-D-rings

Tools Needed

Phillips screw driver

13/16” Socket

7/8” Wrench

9/16” Socket

19mm Socket

18mm Socket

15mm Socket

1/2” Drill Bit

Drill

Cutting Tool

Thread Locker

92117300

Torque Specs

Size Grade 5 Grade 8

5/16” 15 ft/lbs 20 ft/lbs

3/8” 30 ft/lbs 35 ft/lbs

7/16” 45 ft/lbs 60 ft/lbs

1/2” 65 ft/lbs 90 ft/lbs

9/16” 95 ft/lbs 130 ft/lbs

5/8” 135 ft/lbs 175 ft/lbs

3/4” 185 ft/lbs 280 ft/lbs

Photo 1

Photo 2

1- 1162Bag

4– 9/16”x1 1/2” Bolts

6– 9/16” Flat Washers

2– 9/16” Lock Washers

2– 9/16” Lock Nuts

8– 12mm-1.75 Nuts

4– 3/8” x 1 1/2” bolts

4– 3/8” Lock Washers

4– 3/8” Flat Washers

1 2 3 4

Inhaltsverzeichnis

Seite 1

JK WINCH / D-RING MOUNTING SYSTEM Thank you for choosing Rough Country Off road Products Please read instructions before beginning installation. Chec

Seite 2

4. Using a 18mm socket, remove the 4 bolts holding the bumper to the frame horn on the driver and passenger side. See Photo 3. 5. Locate the plug f

Seite 3

Photo 12 13. Reinstall bumper, using the studs from the new bumper bracket, and supplied 12mm-1.75 nuts. Tighten using a 19mm socket. 14. Using a 7/

Seite 4

Maintenance Information 1. Failure to securely tighten all bolts on the winch plate, winch, and fairlead can result in product failure, which mat res

Kommentare zu diesen Handbüchern

Keine Kommentare

Rough-country 1173 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rough-country 1173 herunter. Rough Country 1173 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rough-country 1173