Rough-country 674X Bedienungsanleitung PDF herunterladen

JEEP JK 4” X-SERIES SUSPENSION KIT

Thank you for choosing Rough Country for your suspension needs.

Rough Country recommends a certified technician install this system. In addition to these instructions, professional

knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install

this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read instructions before beginning installation. Check the kit hardware against the parts list. Be sure you have all

needed parts and know where they go. Also please review tools needed list and make sure you have needed tools.

PRODUCT USE INFORMATION

As a general rule, the taller a vehicle is, the easier it will roll. Seat belts and shoulder harnesses should be worn at all

times. Avoid situations where a side rollover may occur. Rough Country makes no claims regarding lifting devices and

excludes any and all implied claims. We will not be responsible for any product that is altered.

This 4” suspension system was developed using a 35X12.50X17 tire with 4.5” to 4.75” of back spacing on aftermarket

wheels. Stock wheels can be used with this kit with up to a 35x12.5 tire, but different tire manufactures designs may re-

sult in a tire width that could result in contact with the lower control arm and/or front sway bar link in a sharp turn. Please

consult with your tire and wheel expert before purchasing. Also note that if wider tires are desired, offset wheels will be

required.

If question exist we will be happy to answer any questions concerning the design, function, and correct use of our prod-

ucts by calling 1-800-222-7023.

This kit features Rough Country’s adjustable joint design. Adjustable end tool is included in kit.

Assemble the joints per the separate instruction sheet Part # 92RCJ120 provided.

IMPORTANT NOTES : Upon completing the install of this kit the draglink must be adjusted to center the steering

wheel BEFORE

the vehicle is driven. Failure to do so will cause a computer error, odd handling, and poor per-

formance.

On Automatic equipped vehicles; due to use of an oversize driveshaft from the factory and inadequate

factory clearance it may be possible for the front driveshaft to come in contact with the automatic transmission

pan tearing the factory boot and rubbing on the shaft. Generally this occurs during heavy articulation when

front sway bar links are disconnected and longer shocks are installed. If this is found to occur, the proper pro-

cedure would be to replace the oversize factory shaft with an aftermarket smaller diameter shaft to increase

clearance between the transmission and front driveshaft. Rough Country does offer this driveshaft if needed.

Additionally on 2012 Models, additional exhaust modification on the passenger side crossover pipe will

be required for adequate clearance on the front driveshaft.

NOTICE TO DEALER AND VEHICLE OWNER

Any vehicle equipped with any Rough Country product should have a “Warning to Driver” decal installed on the inside of

the windshield or on the vehicle’s dash. The decal should act as a constant reminder for whoever is operating the vehi-

cle of its unique handling characteristics.

INSTALLING DEALER - it is your responsibility to install the warning decal and forward these installation instructions on

to the vehicle owner for review. These instructions should be kept in the vehicle for its service

Tools Needed:

10mm Wrench 21mm Socket Jack

21mm Wrench Jack Stand Grinder

18mm Wrench 7/16” Wrench 13/32” Drill Bit

18mm Socket 9/16” Wrench Drill

19mm Wrench 9/16” Socket 19mmDeepWell Socket

Reciprocating Saw 13/16” Socket 7/8” Wrench

5/8” Wrench

1 2 3 4 5 6 ... 10 11

, using a 19mm deep well 10

Inhaltsverzeichnis

Seite 1

JEEP JK 4” X-SERIES SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician

Seite 2

22. Install the supplied bushings and sleeves from 1681Shock bag2 to part # 660586 rear shocks. Install the RCX 2.2 series shocks using the factory ha

Seite 3

POST INSTALLATION 1. Confirm that the draglink was adjusted to the center steering wheel BEFORE the vehicle is driven. Failure to do so will cause

Seite 4

KIT CONTENTS Kit Box 1681X OR 1682X Qty Part # Description 2 94506400 Rear sway bar links 1 1681Bag3 Rear Sway Bar Link Bag 1 1681XBag1 Kit bag

Seite 5

TORQUE SPECIFICATIONS Size Grade 5 Grade 8 5/16” 15 ft/lbs 20 ft/lbs 3/8” 30 ft/lbs 35 ft

Seite 6

FRONT INSTALLATION INSTRUCTIONS 1. Prior to installing this kit, with the vehicle on the ground, measure the heights of your vehicle. This measu

Seite 7

12. Remove the bolts securing the upper control arms to the axle using a 18mm wrench/socket. It will be necessary to cut out the passenger side upper

Seite 8

18. Install the bushings and sleeves from 1681bag2 in the shock box into the RCX shock absorber Part # 660585. Po-sition the cup washer and stem bushi

Seite 9

26. Mark the holes to be drilled and remove the bracket from the frame. See Photo 14. 27. Drill the two holes per side using a 17/64” drill bit. See P

Seite 10 - , using a 19mm deep well

REAR INSTALLATION INSTRUCTIONS 1. Chock front wheels. Jack up the rear of the vehicle and support the vehicle with jack stands, so that the rear whee

Seite 11

12. Assemble the heim joints in the new lower control arms and adjust them to a length of 20 1/2” from center of hole to center of hole and tighten th

Kommentare zu diesen Handbüchern

Keine Kommentare

Rough-country 674X Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rough-country 674X herunter. Rough Country 674X User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rough-country 674X