Rough-country 349.23 Bedienungsanleitung PDF herunterladen

2011-12 2500/3500 Dodge 5” Lift Kit

Drop Brackets

Thank you for choosing Rough Country Suspension for your Off Road needs.

Rough Country recommends a certified technician installs this system. In addition to these instructions, professional

knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to

install this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the ve-

hicle. Average professional install time for this kit is 4-6 hours.

Please read all the instructions before beginning the installation. Check the kit hardware against the kit contents list on

the last page. Be sure you have all the needed parts and understand where they go.

Product Use Information

As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend, because of rollover possibility,

that the vehicle be equipped with a functional roll-bar and cage system. Seat belts and should harnesses should be

worn at all times. Avoid situations where a side rollover may occur.

Also check the steering stabilizer. It is a good idea when adding larger than stock tires to go with a larger bore steering

stabilizer or a dual unit for tires 35” and above. Inspect the stabilizer and replace as necessary.

Braking performance and capability are decreased when significantly large/heavier tires and wheels are used. Take

this into consideration while driving.

Do no add, alter, or fabricate any factory or after-market parts which increase vehicle height over the intended height

of the Rough Country product purchased. Mixing component brands, lifts, and/or combining body lift with suspension

lifts voids all warranties. Rough Country makes no claims regarding lifting devices and excludes any and all implied

claims. We will not be responsible for any product that is altered.

The relocation brackets are used to flatten out the angle of the control arms to maintain your factory handling charac-

teristics of the vehicle. These brackets are designed to use with Rough Country’s 5” Dodge 2500/3500 kit using factory

control arms or adjustable arms at factory lengths.

This suspension system was developed for 37x12.50 tire on an aftermarket 17” x 9” or 20” wheels with a minimum of

5” back spacer. When larger tires are installed, speedometer recalibration is necessary. Due to ride height inconsis-

tencies from the factory you may need to slightly trim the front plastic valance for proper tire clearance.

This kit can also be used a 3500 single rear wheel truck. Use of this kit on a dual rear wheel pickup is not rec-

ommended. Block and u-bolt combinations may vary with 3500 models.

On vehicles equipped with a two piece driveshaft & carrier bearing as on the Mega Cab, there is the potential

for take off vibration, depending on the severity this can be corrected with shimming down the carrier bearing.

Carrier bearing drop kit Part # 1110 is available from Rough Country. Also 2500/3500 trucks with factory over-

load springs the overload will have to be removed for new block and u-bolt installation.

Notice to Dealer and Vehicle Owner

Any vehicle equipped with any Rough country product must have the “Warning to Driver” decal installed on the sun

visor or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling

characteristics. INSTALLING DEALER—It is your responsibility to install the warning decal and to forward

these installation instructions to the vehicle owner for review and to be kept in the vehicle for its service life.

923493000

1 2 3 4 5 6 7 8

Drop Brackets 1
DRILLING TEMPLATE 8

Inhaltsverzeichnis

Seite 1 - Drop Brackets

2011-12 2500/3500 Dodge 5” Lift Kit Drop Brackets Thank you for choosing Rough Country Suspension for your Off Road needs. Rough Country recommends

Seite 2

FRONT SUSPENSION INSTALLATION 1. Secure and block the rear tires of the vehicle on a level concrete or asphalt surface 2. Open the hood and remove t

Seite 3

10. On passenger side remove upper control arm bolt on axle side using a 21mm socket and wrench. Remove bolt from lower control arm on frame side usi

Seite 4

14. Install the supplied flag nut into slotted hole behind body mount. See Photo 10 Install lower control arm drop bracket using supplied 5/8 x 4.5”

Seite 5

24. Install the sway bar drop bracket as shown in Photo 14 and secure to the frame using the factory hardware. Tighten with a 18mm wrench. 25. Inst

Seite 6

5. Remove the cable and place the supplied drilling template in place, making sure the template has the new hole placed directly below factory hole T

Seite 7

1342Bag1 2-14mm x .875 x 2.35 Sleeves 2-9/16” x 5” 4-9/16” Nylocks 2-9/16” Washers 12-7/16” x 1.5” Bolts 12-7/16” Nylocks 24-7/16” Washe

Seite 8 - DRILLING TEMPLATE

POST INSTALLATION INSTRUCTIONS Check all fasteners for proper torque. Check to ensure there is adequate clearance between all rotating, mobile, fixed

Kommentare zu diesen Handbüchern

Keine Kommentare

Rough-country 349.23 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Rough-country 349.23 herunter. Rough Country 349.23 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Rough-country 349.23